Creating a Kolida K9T GPS GSM Network Rover Profile and Connecting to a GPS Net

Creating a Kolida K9T GPS GSM Network Rover Profile and Connecting to a GPS Network Data Correction Service Using MicroSurvey FieldGenius May 4, 2012 © 2012 MicroSurvey Software Inc. Page 2 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile Introduction This guide describes how to create a GPS GSM network rover profile for your Kolida K9T GNSS receiver. Important Note: You only need to create a particular profile once. After that FieldGenius will preserve and use this already-created profile. You are also welcome to create more profiles such as for a UHF radio GPS profile, but in this guide we explain how to create a GSM Network GPS profile. Current Version This guide was written using FieldGenius Version 6.0.1 installed on a Getac PS236 with Windows Mobile 6.1 installed. If you are using a different version, your screens may look differently than what is displayed in this guide. Before you begin Have your Kolida K9T Receiver, data collector with FieldGenius installed, and a SIM card close by. You will need them to complete this guide. Continued on the following page © 2012 MicroSurvey Software Inc. Page 3 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 1  Turn on your Getac PS236. This starts up the Windows Mobile 6.1 Operating system. Note: Don’t be alarmed if your display is slightly different from the image on the right. We may have set up our display differently to yours.  Tap on the button. From within the context menu:  Tap on the FieldGenius menu selection. Note: If you do not see FieldGenius in your menu then you must use File Explorer to go to Programs and find the FieldGenius icon and tap on it. The next time you open this Start menu you will see FieldGenius in the list. This takes you to the Device ID screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 4 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 2 In the Device ID screen:  Enter your License Key in the Key field.  Press the Apply Key button when finished. Important Note: FieldGenius will remember your key, therefore, you will only have to enter your key once. Once a correct key is entered, you will not see this screen again. This takes us to the Project Manager screen after we accept the tip of the day. 3 In the Project Manager screen: Since this is a new installation, we only see the sample project that comes included with FieldGenius. We will create a new project.  Tap on the New Project button. This takes us to the Create New Project screen. Continued on the following page License Keys are provided by the internet registration portal or your dealer. Please contact your dealer for information on License Keys and how to register your new software. © 2012 MicroSurvey Software Inc. Page 5 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 4 In the Create New Project screen:  Enter a name for your new project. In this example, we are calling the project “Friday Job”. You should enter a more appropriate name.  Press the OK button when finished. This opens the Project Review screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 6 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 5 In the Project Review screen: Automap files contain pre-defined descriptions that can be used in FieldGenius. The template library that you select will be copied into the project's folder with a name of yourprojectname_automap.csv, and any changes that you make to the Automap Library will affect only the project library, not the template library. Use the Feature List field to select a feature list that you want to use with the project, for collecting GIS point attributes. The Raw Data File field indicates the name of the raw file that is going to be recorded. You can select a different one by pressing the button and either creating a new raw file or choosing an existing one to open. The Modify Project Information button will take you directly to the Project Information screen. There you can enter notes about the project.  Leave these fields as they are.  Press the Continue button. This takes us to the Unit Settings screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 7 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 6 In the Unit Settings screen:  Select which units you wish to use. Important Note: Once this has been set, you cannot change this project’s units again. Since we typically prefer to work in these same units, we will press the Save As Default button. This will make whatever we select here the future default unit setting.  Press the Save As Default button. This takes us to the Save Project Defaults screen. 7 In the Save Project Defaults screen:  Press the OK button. This returns us to the Unit Settings screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 8 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 8 In the Unit Settings screen:  Press the OK button. This takes us to the FieldGenius Assistant screen. 9 In the FieldGenius Assistant screen: We are prompted to select a coordinate system. Important Note: You must have a coordinate system selected if you wish to work with GPS.  Tap on the Yes button. This takes us to the Coordinate System Settings screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 9 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 10 In the Coordinate System Settings screen:  Select the coordinate system you wish to work in. In this example we will be selecting the UTM83-11 North zone coordinate system with no geoid model. Since we will be typically working in this coordinate system, we will save it as a default.  Press the Save As Default button. This takes us to the Coordinate System Settings screen. 11 In the Coordinate System Settings screen:  Tap on the OK button. This takes us to the Instrument Selection screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 10 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 12 In the Instrument Selection screen:  Tap on the GPS Rover radio button. Note: This is the screen where you can create new instrument profiles, delete existing profiels, or select previously created profiles. This step continues in the Instrument Selection screen. 13 Continuing in the Instrument Selection screen: Notice the Instrument Profile field is now active.  Press the Add button. This takes us to the New Instrument Profile screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 11 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 14 In the New Instrument Profile screen:  Enter a name for your instrument profile in the Profile Name field. In this example, we will call it Kolida K9T Network Rover. Instrument profiles are used to save your particular instrument’s settings so that you don’t have to remember them or have to set them each time you create a new project or select an instrument to use.  Press the Save button. This saves the profile name and returns us to the Instrument Selection screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 12 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 15 In the Instrument Selection screen: With your newly created instrument profile name in the Instrument Profile field,  Press the Edit button. This takes us to the GPS Profile screen. 16 In the GPS Profile screen:  Tap on the Model and Communication button.  Ensure that your receiver is turned on. This takes us to the Model and Communication screen. Continued on the following page © 2012 MicroSurvey Software Inc. Page 13 of 23 Creating a Kolida K9T GPS GSM Network Rover Profile, continued Step Action Display 17 In the Model and Communication screen:  Ensure that the Make field has Kolida selected.  Ensure that the Model field has K9T selected.  Ensure that the Port field is set to Bluetooth.  Press the Bluetooth Search button. This takes us to the Select Bluetooth Device screen. Continued on the following page Note: Although we are using Bluetooth to communicate between our data collector and receiver, you could also use a serial cable. Typically COM1 is the port to select when using a cable. But in this example, we will use Bluetooth. Bluetooth is convenient as there are uploads/Finance/ koida-guide.pdf

• Détails
• Publié le Jan 06, 2021
• Catégorie Business / Finance
• Langue French
• Taille du fichier 1.6872MB