Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

Published techincal data, instructions, and pricing are subject to change witho

Published techincal data, instructions, and pricing are subject to change without notice. Contact your Tnemec technical representative for current technical data, instructions, and pricing. Warranty information: The service life of Tnemec’s coatings will vary. For warranty, limitation of seller’s liability, and product information, please refer to Tnemec’s Product Data Sheets at www.tnemec.com or contact your Tnemec Technical Representative. 6/2014 TNEMEC COMPANY INCORPORATED 6800 Corporate Drive, Kansas City, MO 64120 1-800-TNEMEC1 www.tnemec.com TABLE OF CONTENTS ELS-1 Leading Edge Termination ELS-2 Termination Detail For Embedded Metals ELS-3 Sleeved or Non-Sleeved Pipe Penetration ELS-4 Control or Construction Joints or for Cracks ELS-5 Expansion Joint Treatment Details ELS-6 Construction Joint or Crack for Immersion Service ELS-7 Floor to Wall Transition ELS-8 Floor to Wall Transition with Scrim Reinforcement DETAILS GUIDE ELASTO-SHIELD LINING STANDARD NO. ELS-1 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS LEADING EDGE TERMINATION DETAIL REV. 0 NOTES: 1. A 1/4” X 1/4” SAW-CUT SHALL BE MADE IN THE CONCRETE ALONG ALL LEADING EDGES OF THE COATING. 2. THE SAW-CUT SHALL BE DRIED AND CLEANED OF ALL DUST AND RESIDUE PRIOR TO PRIMING. 3. AREAS NOT TO BE COATED, BUT WHICH ARE ADJACENT TO A LEADING EDGE, SHALL BE NEATLY TAPED OFF AND PROTECTED FROM PRIMER AND TOPCOAT MATERIAL OR OVERSPRAY. 4. PRIMER SHALL BE APPLIED INTO SAW-CUT AREAS. 5. APPLY ELASTO-SHIELD ONTO SAW-CUT AREA, FLOOD INTO SAW-CUT CAVITY WITH TROWEL OR PUTTY KNIFE, AND SMOOTH LEVEL. VERTICAL WILL REQUIRE 2 OR MORE COATS. 6. UPON INITIAL SET OF ELASTO-SHIELD MATERIAL, THE PROTECTIVE TAPE SHALL BE RAZOR-CUT AND REMOVED, LEAVING A STRAIGHT AND NEAT LEADING EDGE. ELASTO-SHIELD SYSTEM EXISTING CONCRETE SUBSTRATE SAWCUT TERMINATION NOTES: 1. IF LINING IS TO BE CARRIED OVER METAL EMBEDMENT, 1/4” X 1/4” SAW-CUT TOE-IN TERMINATION IS STILL REQUIRED. METAL EMBEDMENT EXISTING CONCRETE SUBSTRATE LINING SYSTEM ELASTO-SHIELD NO. ELS-2 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS TERMINATION DETAIL FOR EMBEDDED METALS REV. 0 SAWCUT TERMINATION NOTE: ESTABLISH DEEPER SURFACE PROFILE 1” AROUND O.D. OF PIPE PENETRATION TO LOCK LINING SYSTEM INTO SUB- STRATE. SERIES 265 OR CHEMICAL RESISTANT NON-SAG CAULKING MATERIAL CANT COVE ELASTO-SHIELD SCRIM (OPTIONAL) EXISTING CONCRETE SUBSTRATE LINING SYSTEM EXIST. PIPE OR SLEEVE C L NO. ELS-3 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS SLEEVED OR NON-SLEEVED PIPE PENETRATION REV. 0 ELASTO-SHIELD LINING SYSTEM FILL CONTROL JOINT WITH SERIES 265 CRACKS BETWEEN 1/6” AND 1/8” SHALL BE STRIPE COATED WITH SERIES 265 EXISTING CONCRETE SUBSTRATE FILLER MATERIAL NO. ELS-4 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS CONTROL OR CONSTRUCTION JOINTS OR FOR NON-MOVING CRACKS REV. 0 NOTE: FLEXIBLE JOINT SEALANT WIDTH-TO-DEPTH RATIO SHOWN APPROXIMATELY 2:1. ELASTO-SHIELD LINING SYSTEM BACKER ROD COMPRESSED MIN 25% AND SERIES 265 OR FLEXIBLE JOINT SEALANT EXISTING CONCRETE SUBSTRATE EXISTING ISOLATION NO. ELS-5 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS EXPANSION JOINT TREATMENT DETAIL REV. 0 JOINT MATERIAL NOTES: 1. PREPARE CRACK OR JOINT USING A CRACK CHASING TOOL OR CHIPPING GUN. FOLLOW THE CRACK MAKING A 1/2” WIDE X 1/2” DEEP “V” CENTERED ON THE CRACK. REMOVE ALL DUST AND DEBRIS. 2. PREPARE CONCRETE SURFACE IN ACCORDANCE WITH THE RESPECTIVE ELASTO-SHIELD PRODUCT DATA SHEET AND APPLICATION GUIDELINES. 3. APPLY SERIES 265 IN A 2-4” WIDE STRIP CENTERED OVER THE JOINT. USE MASKING TAPE TO KEEP BOUNDARY TAPE LINES STRAIGHT AND WITHIN STRIP WIDTH. REMOVE TAPE WHILE SERIES 265 IS WET. ALLOW SERIES 265 TO CURE MINIMUM 4 HOURS. 4. APPLY SPECIFIED ELASTO-SHIELD LINING SYSTEM IN ACCORDANCE WITH THE PRODUCT DATA SHEET AND APPLICATION GUIDE. EXISTING CONCRETE SUBSTRATE FLOORING SYSTEM CHIP OUT ANGLE AROUND CRACK SERIES 265 JOINT OR CRACK NO. ELS-6 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS CONSTRUCTION JOINT OR CRACK FOR IMMERSION SERVICES REV. 0 ELASTO-SHIELD 45º CANT COVE OR FILLET 1” HEIGHT USING SERIES 265 OR 218 ELASTO-SHIELD SYSTEM EXISTING CONCRETE SUBSTRATE NO. ELS-7 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS FLOOR TO WALL TRANSITION REV. 0 45º CANT COVE USING EPOXY MORTAR 6” 6” ELASTO-SHIELD SYSTEM 12” SCRIM EMBEDDED & SATURATED WITH 264 EXISTING CONCRETE SUBSTRATE NO. ELS-8 TNEMEC ELASTO-SHIELD STANDARD LINING DETAILS FLOOR TO WALL TRANSITION WITH SCRIM REINFORCEMENT REV. 0 uploads/Geographie/ details-guide-elasto-shield-lining-standard.pdf