Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

Updated February 2013 1 Guide to Insulation Product Specifications Introduction

Updated February 2013 1 Guide to Insulation Product Specifications Introduction The Guide to Insulation Product Specifications was updated by the National Insulation Association Technical Information Committee in February 2013 after the Committee Days meeting. This guide lists ASTM, federal and military specifications that pertain to the thermal insulation industry. It encompasses both industrial and commercial mechanical insulations as well as building envelope and fire resistance insulations. Related application and finishing accessory materials also are included. Some government construction agencies (General Services Administration, Department of Housing and Urban Development, Department of Defense, Corps of Engineers, etc.) issue specifications or standards that designated insulation materials. This guide is intended to serve the limited purpose of describing, in a general way, the specifications and standards so designated. It should be kept in mind that the materials listed in this guide are subject to change, as are the specifications and standards themselves. Users are encouraged to review the current version of the applicable specification and/or standard. This guide organizes each specification by type (ASTM, federal, or military), number and title and describes its scope. NIA Associate Members that manufacture products that claim conformance to the referenced specification are listed below each specification. Do not rely upon the guide to determine whether a product meets contract specifications or to obtain approvals under purchase orders or contracts. These determinations must be made by careful examination of the contract specifications, the manufacturer’s literature, and the provision of the government specification or standard referred to in the contract documents. For specific product information and specifications compliance, consult the particular manufacturer. Ordering Information To order a copy of an ASTM specification, contact the following: Order Department ASTM International 100 Barr Harbor Drive West Conshohocken, PA 19428 Tel: (610) 832-9585; Fax (610) 832-9555 www.astm.org Requests for copies of federal and military specifications should be made on company letterhead and sent to the following address: 700 Robbins Ave. Philadelphia, PA 19111-5094 (Allow 8-10 working days for processing) Hard copies of this guide can be downloaded from the NIA website: NIA 12100 Sunset Hills Rd. Suite 330 Reston, VA 20190 Tel: (703) 464-6422; Fax: (703) 464-5896 www.insulation.org ASTM Guides, Practices and Test Methods The following selected ASTM standards describe test methods and practices to determine specific characteristics of building and construction materials and shall not be used to specify materials. These Updated February 2013 2 methods may be referenced in ASTM standards or other specification and standards. ASTM standards must be reviewed every five years and, if not revised, either approved again or withdrawn. Standards pertaining to thermal insulation generally are developed by ASTM Committee C-16 on Thermal Insulation and thus are identified with the prefix C followed by a three- or four-digit number. A two-digit number following the dash (omitted in this document) indicates the year that the standard was adopted or, if revised, the year of last revision. Users are advised to refer to the current version of the standard in effect at the time of preparation of purchase documents and specifications. C165 Test Method for Measuring Compressive Properties of Thermal Insulations. C167 Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations. C168 Terminology Relating to Thermal Insulating Materials C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded Hot-Plate Apparatus C203 Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation C209 Test Methods for Cellulosic Fiber Insulation Board C240 Test Methods of Testing Cellular Glass Insulation Block C302 Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation C303 Test Method for Density and Dimensions of Preformed Block-Type Thermal Insulation C335 Test Method for Steady-State Heat Transfer Properties of Horizontal Pipe Insulation C356 Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heath C390 Criteria for Sampling and Acceptance of Preformed Thermal Insulation Lots C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation C419 Practice for Making and Curing Test Specimens of Mastic Thermal Insulation Coatings C423 Test Method for Sound Absorption and Sound Absorption Coefficiencies by the Reverberation Room Method C447 Practice for Estimating the Maximum Use Temperature of Thermal Insulations C450 Practice for Prefabrication and Field Fabrication of Thermal Insulating Fitting Cover for NPS Piping, Vessel Lagging, and Dished Head Segments C461 Test Methods for Mastics and Coatings Used with Thermal Insulation C488 Test Method for Conducting Exterior Exposure Tests of Finishes for Thermal Insulation C518 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus C585 Practice for Inner and Outer Diameters of Rigid Thermal Insulation for Nominal Sizes of Pipe and Tubing (NPS System) C634 Terminology Relating to Environmental Acoustics C647 Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation C653 Guide for Determination of the Thermal Resistance of Low-Density Blanket-Type Mineral Fiber Insulation C680 Practice for Determination of Heat Gain or Loss and the Surface Temperatures of Insulated Pipe and Equipment Systems by the Use of a Computer Program C692 Test Method for Evaluating the Influence of Thermal Insulations on the External Stress Corrosion Cracking Tendency of Austenitic Stainless Steel C740 Practice for Evacuated Reflective Insulation in Cryogenic Service C755 Practice for Selection of Vapor Retarders for Thermal Insulation C795 Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel C871 Test Methods for Chemical Analysis of Thermal Insulation Materials for Leachable Chloride, Fluoride, Silicate, and Sodium Ions C921 Practice for Determining the Properties of Jacketing Materials for Thermal Insulation C929 Practice for Handling, Transporting, Shipping, Storage, Receiving, and Application of Thermal Insulation Materials to Be Used Over Austenitic Stainless Steel C930 Classification of Potential Health and Safety Concerns Associated with Thermal Insulation Materials and Accessories Updated February 2013 3 C1045 Practice for Calculating Thermal Transmission Properties from Steady-State Heat Flux Measurements C1058 Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation C1101/C1101M Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation C1104/C1104M Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation C1129 Standard Practice for Estimation of Heat Savings by Adding Thermal Insulation to Bare Valves and Flanges C1199 Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods C1335 Test Methods for Measuring Non-Fibrous Content of Man-made Rock and Slag Mineral Fiber Insulation C1338 Test Method for Determining Fungi Resistance of Insulation Materials and Facings C1363 Standard Test Method for the Thermal Performance of Building Assemblies by Means of a Hot Box C1617 Standard Practice for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Metals C1639 Standard Specification for Fabrication of Cellular Glass Pipe and Tubing Insulation C1728-12 Standard Specification for Flexible Aerogel Insulation C1729 Standard Specification for Aluminum Jacketing for Insulation C1767 Standard Specification for Stainless Steel Jacketing for Use over Thermal Insulation D792 Test Methods for Density and Specific Gravity Cellular Density of Plastics by Displacement D1621 Test Method for Compressive Properties of Rigid Cellular Plastics D1622 Test Method for Apparent Density of Rigid Cellular Plastics D2126 Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging E84 Test method for Surface Burning Characteristics of Building Materials E90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions E96 Test Method for Water Vapor Transmission of Materials E119 Test Method for Fire Tests of Building Construction and Materials E136 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C E176 Terminology Related to Fire Standards E477 Test Method for Measuring Acoustical and Airflow Performance of Duct Liner Materials and Prefabricated Silencers E814 Test Method for Fire Tests of Through-Penetration Fire Stops E2231 Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess the Surface Burning Characteristics F683 Practice for Selection and Application of Thermal Insulation for Piping and Machinery ASTM Specifications A240/A240M Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels Covers chromium, chromium-nickel, and chromium-manganese-nickel stainless and heat-resisting steel plate, sheet, and strip for pressure vessels. • ITW Insulation Systems/Pabco-Childers Metals • R.P.R. Products, Inc. A653/A653M Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process Updated February 2013 4 • R.P.R. Products, Inc. A792/A792M Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process • ITW Insulation Systems/Pabco-Childers Metals • R.P.R. Products, Inc. B209 Aluminum and Aluminum-Alloy Sheet and Plate [Metric] Covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate. • ITW Insulation Systems/Pabco-Childers Metals • R.P.R. Products, Inc. C195 Mineral Fiber Thermal Insulating Cement Covers mineral fiber thermal insulating materials in the form of dry cement which, when mixed with a suitable proportion of water, applied as a plastic mass, and dried in place, affords resistance to heat transmission on surfaces operating at temperatures between 100° and 1,600°F. Replaces federal specification Ss-C-160A in part. C196 Expanded or Exfoliated Vermiculite Thermal Insulating uploads/Litterature/ specs-guide.pdf