Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

ELECTRICALINSTALLATION AND MAINTENANCE NC II: UC1: Perform roughing- in activit

ELECTRICALINSTALLATION AND MAINTENANCE NC II: UC1: Perform roughing- in activities, wiring and cabling works for single-phase distribution, power, lighting and auxiliary systems LO1: Install Electrical Metallic /Non-Metallic (Pvc Conduit) STUDY GUIDE (255 hours) Prepared by: Rommel A. Selga,Trainer INTRODUCTION: The Electrical Installation and Maintenance NC II Qualification consists of competencies that a person must achieve to enable him/her to install and maintain electrical wiring, lighting and related equipment and systems where the voltage does not exceed 600 volts in residential houses/buildings. This unit covers the knowledge, skills and attitudes on installing electrical metallic and non-metallic conduit, wire ways and cable clamp, auxiliary terminal cabinet and distribution frame panel board/safety switch and used in roughing-in based on the required performance standards. This unit also covers the outcomes required in preparing for cable pulling and installation, performing wiring and cabling lay-out and notifying completion of work for single-phase distribution, power, lighting and auxiliary systems. OBJECTIVES At the end of this module, you should be able to: 1. Install electrical metallic /nonmetallic (PVC conduit) 2. Install wire ways and cable tray 3. Install auxiliary terminal cabinet and distribution panel 4. Prepare for cable pulling and installation 5. Perform wiring and cabling lay out 6. Notify completion of work KEY CONCEPTS UNIT I : Install electrical metallic /nonmetallic (PVC conduit)  Interpret electrical wiring diagrams and mechanical drawings  Identify proper usage and types of conduits, fittings in electrical installation.  Identify technique of installation and bending of conduit and fitting.  Apply proper usage of safety harness.  Interpret plan and details drawing.  Practice proper handling of materials, tools and equipment  Practice procedure in proper bending of conduits  Practice procedure in installing conduits  Perform the installation economically UNIT II : Install wire ways and cable tray  Identify use of materials, tools and equipment  Interpret electrical/mechanical drawing  Determine suitability for installation and used of bus way, cable tray, fittings and panels, conformity with the provision of the PEC Code.  Practice wire way and cable tray installation  Practice proper use of safety harness (PPE)  Interpret technical plan  Use effective communication skills (written and oral )  Practice effective use of measuring tape  Perform the installation economically UNIT III : Install auxiliary terminal cabinet and distribution panel  Learn and apply mensuration  Determine blue print reading and materials specification.  Read proper proofing standards  Perform proper procedure in installation of auxiliary terminal cabinet and distribution panel.  Apply proper use of safety harness (PPE).  Interpret technical plan  Practice effective use of measuring devices  Practice proper handling of tools and equipment  Install terminal cabinet and distribution panel  Perform the installation economically UNIT IV : Prepare for cable pulling and installation  Read and familiarize: o mensuration o Blue print reading and materials specification. o uses of wires, cables and tools o required sizes of cable based on PEC Wire Table  Prepare cable for installation  Interpret technical plan and drawing.  Practice effective use of measuring tapes  Practice proper handling of tools and equipment  Apply methods and techniques in various type of wiring wires and cables. UNIT V : Perform wiring and cabling lay out  Read and familiarize: o Mensuration o Blue print reading and materials specification o Application of pulling compound o Methods in cable pulling  Interpret technical plan and drawing.  Apply methods in cable pulling  Follow procedures in bending radius and loop tolerances for cables UNIT VI: Notify completion of work  Describe processes, Operations Systems - Maintenance of tools & materials - Storage of tools  Check and conform the installation based on job requirement  Practice good housekeeping.  Perform commissioning activities LEARNING RESOURCES 1. Competency Based Learning Materials 2. Online Learning Materials uploaded on LMS 3. Self-paced Learning Materials uploaded in LMS (Interactive Book-type lessons, H5Ps, Online presentations, etc) 4. Webinars 5. Demonstration Videos 6. Lecture Videos 7. Task Sheets and Performance Criteria Checklist STUDY QUESTIONS UNIT I : Install electrical metallic /nonmetallic (PVC conduit)  How to Interpret electrical wiring diagrams and mechanical drawings  How to Identify proper usage and types of conduits, fittings in electrical installation.  How to Identify technique of installation and bending of conduit and fitting.  How to Apply proper usage of safety harness.  How to Interpret plan and details drawing.  How to Practice proper handling of materials, tools and equipment  How to Practice procedure in proper bending of conduits  How to Practice procedure in installing conduits  How to Perform the installation economically UNIT II : Install wire ways and cable tray  How to Identify use of materials, tools and equipment  How to Interpret electrical/mechanical drawing  How to Determine suitability for installation and used of bus way, cable tray, fittings and panels, conformity with the provision of the PEC Code.  How to Practice wire way and cable tray installation  How to Practice proper use of safety harness (PPE)  I How to nterpret technical plan  How to Use effective communication skills (written and oral )  How to Practice effective use of measuring tape  How to Perform the installation economically UNIT III : Install auxiliary terminal cabinet and distribution panel  How to Learn and apply mensuration  How to Determine blue print reading and materials specification.  How to Read proper proofing standards  How to Perform proper procedure in installation of auxiliary terminal cabinet and distribution panel.  How to Apply proper use of safety harness (PPE).  Interpret technical plan  How to Practice effective use of measuring devices  How to Practice proper handling of tools and equipment  How to Install terminal cabinet and distribution panel  How to Perform the installation economically UNIT IV : Prepare for cable pulling and installation  How to Read and familiarize: o mensuration o Blue print reading and materials specification. o uses of wires, cables and tools o required sizes of cable based on PEC Wire Table  How to Prepare cable for installation  How to Interpret technical plan and drawing.  How to Practice effective use of measuring tapes  How to Practice proper handling of tools and equipment  How to Apply methods and techniques in various type of wiring wires and cables. UNIT V : Perform wiring and cabling lay out  How to Read and familiarize: o Mensuration o Blue print reading and materials specification o Application of pulling compound o Methods in cable pulling  How to Interpret technical plan and drawing.  How to Apply methods in cable pulling  How to Follow procedures in bending radius and loop tolerances for cables UNIT VI: Notify completion of work  How to Describe processes, Operations Systems - Maintenance of tools & materials - Storage of tools  How to Check and conform the installation based on job requirement  How to Practice good housekeeping.  How to Perform commissioning activities ACTIVITIES Online Activities 1. Orientation Program a. Attend the trainees Induction Program to be held via Google Meet Webinar on August 03,2020, 08:00 AM b. Access the Learning Management Systemand read the Study Guide. c. Participate in the Discussion forum entitled “Self-Introduction”. d. Take the Pre-test Exam 2. Daily Webinars (09:00am) – Attendance is checked 3. Online learning activities a. Read eLearning contents in books and presentations b. View videos; c. Use interactive eLearning materials d. Take quizzes; (graded) e. Participate in Forums; (required) f. Use chat for queries and communications Note: A badge shall be awarded to those who participated in all forum discussions and pass the quizzes and posttest 4. Workshops (Individual) a. The learner shall prepare all the documents needed for the lessons and assigned topics to be uploaded in the development site. b. The learner can access the development site using the assign username and password given by the administrator c. The learner shall refer to the task sheet uploaded in the training site for his/her hands-on exercises with concrete documentation for validation. 5. Role-play and or demonstration on how to conduct and participate in a webinar: a. Orientation b. Monitoring Learning Activities 6. Institutional Assessment a. Demonstration with oral questioning b. Face-to-face learning Important skills to be learned: 1. Communication Skills (Oral & written) 2. Calibrating Skills 3. Basic Computer Skills 4. Cooking/ Culinary Skills 5. Basic Mathematical skills (conversion, weights and measurements, ratios and proportions 6. Recording and reporting skills 7. Computation for recovery/ yields STUDY SCHEDULE Please refer to the schedule for your reference. DATE /PERIOD TOPIC/S ACTIVITY VENUE AND TIME NO OF HOURS August 03,2020 A.M Orientation to the blended learning program Trainees Induction Program Google Meet 08:00Am 1 hour Read Study Guide Online LMS 20 minutes Participate in the Discussion forum entitled “Self- Introduction”. Online LMS 25 minutes Take the Pre-test Exam Online LMS 30 minutes August 3, 2020 P.M. Lesson 1 : Install electrical metallic /nonmetallic (PVC conduit) Online: uploads/s3/ study-guide 19 .pdf