Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

CZ 40 P - INSTRUCTION MANUAL 2 Before handling the pistol read this manual care

CZ 40 P - INSTRUCTION MANUAL 2 Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional discharge and could cause injury, death or damage to property. The same consequences can be caused by unauthorized modifications or adjustments, corrosion, or use of non-standard or damaged ammunition. In these cases the manufacturer shall not be responsible in any manner whatsoever for the resultant consequences. Before leaving the factory this pistol was tested, carefully inspected, and packed. CZ cannot accept responsibility for product handling while in transit, or upon leaving the factory. Therefore, please examine this pistol carefully at the time of purchase to ensure that it is unloaded and undamaged. This instruction manual should always accompany this pistol and that even in the case of the loan or sale of this pistol. CONTENTS SAFETY INSTRUCTIONS 3 PISTOL DESCRIPTION AND TERMINOLOGY 5 Safety Features 6 OPERATING INSTRUCTIONS 7 Ammunition 7 Removal of the Magazine 7 Magazine Loading 7 Pistol Loading 8 Hammer Decocking 8 Unloading the Pistol 8 Sight Adjustment 8 Special Accessories Attachment 9 MAINTENANCE INSTRUCTIONS 9 Stripping for Cleaning - Disassembly 9 Magazine Disassembly 9 Cleaning the Pistol 10 Cleaning the Barrel Bore and the Cartridge Chamber 10 Cleaning of Other Pistol Parts 10 Preserving 10 TROUBLESHOOTING, CAUSES AND REMEDIES 11 ILLUSTRATION AND LIST OF PARTS 12 TECHNICAL SPECIFICATIONS 14 CZ 40 P - INSTRUCTION MANUAL 3 SAFETY INSTRUCTIONS Always follow the safety instructions for your safety and the safety of others. 1. Always handle your pistol as if it were loaded. 2. Never point your pistol at anything you do not intend to shoot. 3. Never take anyone's word that a gun is unloaded. 4. Always make sure that your pistol is not loaded before laying it down, or handing it to another person. 5. Always keep and carry your pistol empty, with the hammer forward except when you intend to shoot. 6. Never abuse your pistol by using it for any purpose other than shooting. 7. Never leave the pistol cocked and ready to fire unattended. 8. Before loading your pistol be sure that the barrel bore, chamber, and action are clean and clear of obstructions. After shooting, clean the dirtied pistol as soon as possible. 9. Always use only clean, dry, original high quality commercially manufactured ammunition, which is appropriate to the caliber of your pistol. 10. Never drink alcoholic beverages or take drugs before or during shooting. 11. Always wear safety glasses and ear protection when shooting. 12. Always keep clear and keep others clear of the ejection port. 13. Never squeeze the trigger or put your finger in the trigger guard until you are aiming at a target and ready to shoot. 14. Always be absolutely sure of your target, and the area behind it, before you squeeze the trigger. A bullet could travel through or past your target up to several hundred meters. 15. Never shoot at a hard surface such as rock, or a liquid surface such as water. 16. Never fire your pistol near an animal unless it is trained to accept the noise. 17. Never indulge in "horseplay" while holding your pistol. 18. Failure to fire: In case no discharge been initiated press the trigger again and try to activate the primer using DA mode of fire (see herein further). If even after this the cartridge is not discharged, hold the pistol, keeping it pointed towards the target, or a safe open area and wait 30 seconds. If a hangfire (slow ignition) has occurred, the round will fire within 30 seconds. If the round does not fire, remove the magazine, eject the round and examine the primer; if the firing pin indent on the primer is light, or off center, or non-existent, have the pistol examined by a competent gunsmith. CZ 40 P - INSTRUCTION MANUAL 4 19. Always make sure your pistol is not loaded before cleaning, storing or travelling. 20. Always keep and store your pistol and ammunition in separate locked receptacles out of reach and sight of children and untrained people. 21. Never alter any parts of your pistol as the safety and proper function of your pistol could be seriously compromised. 22. Always be aware that corrosion, use of damaged ammunition, dropping the pistol on hard surfaces or other "coarse treatment" could cause damage you may not see. If something like this happens allow the pistol to be examined and tested by a competent gunsmith. CZ 40 P - INSTRUCTION MANUAL 5 PISTOL DESCRIPTION AND TERMINOLOGY Nomenclature of all CZ 40 P parts are presented in the section Illustration and List of Parts. The CZ 40 P pistol is a semi-automatic handgun incorporating short recoil, designed for aimed shooting up to 50 m distances. The CZ 40 P utilizes the locked breech principle. It is fitted with a trigger mechanism adapted to operate both in SA and DA modes of fire, a firing pin safety, safety stop on the hammer and hammer decocking device dropping the hammer safely to its rest position. Characteristic features of the CZ 40 P are: - Comfortable grip and balance in either hand - Good results at instinctive shooting (without aiming) - Low trigger pull weight - High accuracy of fire - Long service life - High reliability, even with various types of cartridges - The sights are fitted with a three-dot illuminating system for better aiming in poor visibility conditions CZ 40 P - INSTRUCTION MANUAL 6 Comments: SA (Single Action) The trigger mechanism operates in a single action mode of fire. The hammer is cocked manually and then after pressing the trigger the pistol is fired. The trigger travel is short, and pull weight is low. After each discharge the hammer remains cocked. DA (Double Action) The trigger mechanism operates in a double action mode of fire. The hammer is cocked, released and the pistol fired by one pull of the trigger. The trigger travel is longer, and trigger pull weight is higher than at SA mode of fire. Safety Features Trigger Guard Prevents unintentional pressing of the trigger, for example when the pistol is dropped. Inertia Firing Pin The design of the firing pin prevents the firing pin from protruding through the face of the slide when the hammer is in its rest position. This eliminates the possibility of a discharge when a loaded pistol is dropped on the hammer. Firing Pin Safety The firing pin safety keeps the firing pin blocked until the trigger is pulled. This safety device minimizes the risk of accidental discharge through mishandling such as when a loaded pistol is dropped. Decocking Serves for the lowering of the hammer from the cocked position to the hammer safety notch position. There is no necessity to manipulate the trigger and hammer manually. This device is especially useful when a cartridge is loaded in the chamber. In this state, when the hammer is decocked, the pistol is safe for all normal handling and yet is ready for immediate use. Safety Stop on the Hammer A half-cock safety notch is on the hammer so as to prevent it from striking the firing pin when the hammer is manually cocked, and a thumb could slip. When the hammer is on the safety stop, it is not leaning against the firing pin stop, but its position is further back. CZ 40 P - INSTRUCTION MANUAL 7 OPERATING INSTRUCTIONS Ammunition Use only factory-manufactured ammunition of appropriate caliber, which are in compliance with CIP regulations (International Proof Commission for Firearms) or SAAMI (Sporting Arms and Ammunition Manufacturers' Institute Inc. of the United States). The use of other cartridges could damage the handgun or cause injury to the shooter. Removal of the Magazine Hold the pistol in your right/left hand and depress the magazine catch with the thumb/middle finger and by the other hand remove the magazine. This pistol model is equipped with the user type magazine catch which can be reversed by gunsmith for the right or left hand operation. Magazine Loading Without Magazine Loader With the open end uppermost, grasp the magazine in one hand. Place a cartridge on the magazine follower. Press the cartridge down and back until it touches the rear flat edge of the magazine. Place the next cartridge on top of the previous cartridge and press down and back. We recommend that when some cartridges are already loaded in the magazine, depress them slightly with the thumb of the hand which holds the magazine. Using Magazine Loader With open end uppermost grasp magazine in one hand. Place the magazine loader from above over the magazine. Rest the magazine loader against a fixed pad and pressing down the magazine loader partially insert the magazine follower into inner space of the magazine. Place a cartridge to thus created space above the follower, release the magazine loader and insert the cartridge to the rear until it touches the rear flat edge of the magazine. Press uploads/Geographie/ cz-40p.pdf