Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

Installation Guide Installatiehandleiding Guide d'installation Installationsanl

Installation Guide Installatiehandleiding Guide d'installation Installationsanleitung Guida di installazione Guía de instalación Installationshandbok 2 RangeMaxTM ADSL Modem Wireless Router DG834PN Start Here Before you begin, locate the ADSL configuration information from your Internet Service Provider (ISP). Also, if you purchased the DG834PN in a country where a microfilter is not included, you must acquire one. Set up the Router 1. CONNECT THE DG834PN TO THE ADSL LINE ADSL signals degrade phone sound quality. Microfilters block such problems and are required for each phone or fax. There are two types: one-line microfilters; and two-line microfilters, which include a built-in splitter. Sharing a phone outlet with two devices requires a splitter. The procedure below illustrates using a two-line combo microfilter/splitter. You can accomplish the same result using a one-line microfilter with a separate phone line splitter. a. Insert the filter into the phone outlet and connect the phone to the phone connector (A). b. Turn off your computer. Phone Phone ADSL Line Two-Line Combo Microfilter/Splitter One-Line Microfilter Splitter 3 c. Connect the ADSL port (B) of the DG834PN to the ADSL connector of the two-line filter. Note: Improperly connecting a filter to your DG834PN will block ADSL signals and prevent connecting to the Internet. d. Connect the NRJ-45 Ethernet cable (C) from a LAN port of your DG834PN to the Ethernet adapter in your computer. Note: The unshielded RJ-45 Ethernet cable is supplied for the connection of the NETGEAR product to your PC and is not intended for connection to the telecommuni- cations network. e. Plug in the router and verify the following: • The power light is lit after applying power to the router. • The ADSL link light is solid green, indicating a link has been established to the ADSL network. Note: You can use the router configuration utility to turn the antenna lights off. f. Now, turn on your computer and verify the following: • The local lights are lit for any connected computers. • If software usually logs you in to the Internet, do not run it. • The Internet Explorer Tools Internet Options Connections page should be set to “Never dial a connection.” g. Install a filter on each phone device that shares the phone line with your router. Note: Use one-line filters for connecting additional phones. 1 4 2. LOG IN TO THE DG834PN Note: Your computer needs to be configured for DHCP. a. Connect to the router by typing http://192.168.0.1 in the address field of your Internet browser. b. When prompted, enter admin for the user name and password for the password, both in lower case letters. After logging in, you will see the menu below. If you do not see the menu above, click the Setup Wizard link on the upper left of the main menu. 3. CONNECT TO THE INTERNET a. Choose your country and language. Click Next to let the Setup Wizard detect the type of Internet connection your have. b. Follow the steps in the Setup Wizard to input the Internet configuration parameters from your ISP. Note: If you were unable to connect to the router, please refer to the Troubleshooting Chapter in the Reference Manual on the Resource CD that came with the router. Now, Set Up Wireless Connectivity 1. Configure the DG834PN Wireless Settings a. If you are not already logged in the DG834PN, type http://192.168.0.1 in your browser and click Enter. 5 When prompted, type admin for the user name and password for the password, both in lower case letters. b. Click Wireless Settings in the DG834PN main menu. Select a Region. Do not change the other settings. Click Apply. 2. Configure the computer’s Wireless Adapter Settings Configure the wireless adapter of your computer to match these settings exactly. Warning: The SSID is case sensitive. Entering nETgear will not work. Use these settings to verify that you have wireless connectivity. Set up wireless security after you are sure you have wireless connectivity. 3. Verify Wireless Connectivity Verify wireless connectivity. Connect to the Internet or log in to the DG834PN from a computer with a wireless adapter. For wireless connectivity problems, see the Troubleshooting Tips below or in the Reference Manual on the CD. You can use the Dome LED link in the main configuration menu to control when the antenna lights are on or turn them off completely. 4. Implement Wireless Security • Wireless networks are vulnerable to intrusion if you do not use the available security options. The wireless security options you choose depend on the options available in your wireless computers. • Implement wireless security according to the instructions in the Wireless chapter of the Reference Manual on the CD. You are now wirelessly connected to the Internet! WIRELESS FEATURE DEFAULT SETTING Network Name (SSID) NETGEAR WEP/WPA Security Disabled 6 Troubleshooting Tips Here are some tips for correcting simple problems you may have. Be sure to restart your network in the correct sequence. Always follow this sequence: 1) Unplug and turn off the DG834PN. Turn off the computer. 2) Plug in and turn on the DG834PN, wait two minutes. 3) Turn on the computer. Make sure the Ethernet cables are securely plugged in. • For each powered on computer connected to the DG834PN with a securely plugged in Ethernet cable, the corresponding DG834PN LAN port status light will be lit. The label on the bottom of the ADSL modem wireless router identifies the number of each LAN port. • The Internet port status light on the ADSL modem wireless router will be lit if the phone cable is plugged in securely to the DG834PN ADSL port and the DG834PN is turned on. Make sure the computer & router wireless settings match exactly. The Wireless Network Name (SSID) and security settings (WEP/WPA, MAC access control list) of the DG834PN and wireless computer must match exactly. Make sure the network settings of the computer are correct. • LAN and wirelessly connected computers must be configured to obtain an IP address automatically via DHCP. For help with this, please see the Manual on the CD. Check the router status lights to verify correct router operation. • If the Power light does not turn solid green within 2 minutes after turning the router on, reset the router according to the instructions in the Manual on the CD. • If the Wireless light does not come on, verify that the wireless feature is turned on according to the instructions in the Manual on the CD. Technical Support Thank you for selecting NETGEAR products. After completing the Smart Wizard configuration assistant, register your product at http://www.NETGEAR.com/register. Registration is required before you can use our telephone support service. Go to http://kbserver.netgear.com/products/DG834PN.asp for product updates and Web support. 7 Modem/Routeur ADSL sans fil RangeMaxTM DG834PN Pour commencer Avant de commencer, demandez à votre fournisseur d'accès à Internet (FAI) les paramètres de configuration de votre ligne ADSL. Si vous avez acheté le DG834PN dans un pays où le microfiltre n'est pas inclus, vous devez vous en procurer un. Configuration du routeur 1. CONNEXION DU DG834PN À LA LIGNE ADSL Les signaux ADSL nuisent à la qualité des communications téléphoniques. Les microfiltres permettent de remédier à ce problème et sont nécessaires pour chaque téléphone et télécopieur. Il existe deux types de microfiltres : ceux conçus pour une ligne et ceux conçus pour deux lignes, avec répartiteur intégré. L'utilisation de deux appareils sur une seule prise téléphonique nécessite l'installation d'un répartiteur. La procédure ci-après illustre l'utilisation d'une combinaison microfiltre/répartiteur pour deux lignes. Vous pouvez parvenir aux mêmes résultats à l'aide d'un microfiltre pour une ligne et d'un répartiteur pour ligne téléphonique séparée. a. Branchez le microfiltre entre la prise murale et le connecteur de téléphone (A). b. Eteignez votre ordinateur. Phone Phone ADSL Line Combinaison microfiltre / répartiteur pour deux lignes Microfiltre pour une ligne Répartiteur 8 c. Raccordez le port ADSL (B) du DG834PN au connecteur du microfiltre pour deux lignes. Remarque : si vous branchez par erreur un microfiltre sur votre routeur DG834PN, votre ligne ADSL sera bloquée et vous ne pourrez pas vous connecter à Internet. d. Branchez le câble Ethernet RJ-45 (C) d'un port LAN de votre routeur DG834PN sur l'adaptateur Ethernet de votre ordinateur. Remarque : Le câble Ethernet RJ-45 non blindé est fourni pour relier les produits NETGEAR à votre ordinateur. Il n'est pas conçu pour les connexions au réseau de télécommunication. e. Branchez le routeur et vérifiez les points suivants : • Le voyant d'alimentation s'allume lorsque vous mettez le routeur sous tension. • Quand le voyant ADSL est vert, il indique que la communication a été établie avec le réseau ADSL. Remarque : vous pouvez employer l'utilité de configuration du routeur pour arrêter les lumières d'antenne. f. A présent, allumez votre ordinateur et vérifiez les points suivants : • Les voyants locaux sont allumés pour chaque ordinateur connecté. • Si, d'habitude, un programme vous connecte directement à Internet lors du démarrage, désactivez-le. • Dans Internet Explorer, l'option « Ne jamais établir de connexion » de l'onglet Connexions (choisissez Outils, uploads/Ingenierie_Lourd/ install-guide 6 .pdf