Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

Details guide elasto shield lining standard

DETAILS GUIDE ELASTO -SHIELD LINING STANDARD TABLE OF CONTENTS ELS - Leading Edge Termination ELS - Termination Detail For Embedded Metals ELS - Sleeved or Non-Sleeved Pipe Penetration ELS - Control or Construction Joints or for Cracks ELS - Expansion Joint Treatment Details ELS - Construction Joint or Crack for Immersion Service ELS - Floor to Wall Transition ELS - Floor to Wall Transition with Scrim Reinforcement TNEMEC COMPANY INCORPORATED Corporate Drive Kansas City MO - -TNEMEC www tnemec com Published techincal data instructions and pricing are subject to change without notice Contact your Tnemec technical representative for current technical data instructions and pricing Warranty information The service life of Tnemec ? s coatings will vary For warranty limitation of seller ? s liability and product information please refer to Tnemec ? s Product Data Sheets at www tnemec com or contact your Tnemec Technical Representative CELASTO -SHIELD SYSTEM SAWCUT TERMINATION EXISTING CONCRETE SUBSTRATE NOTES A ? X ? SAW-CUT SHALL BE MADE IN THE CONCRETE ALONG ALL LEADING EDGES OF THE COATING THE SAW-CUT SHALL BE DRIED AND CLEANED OF ALL DUST AND RESIDUE PRIOR TO PRIMING AREAS NOT TO BE COATED BUT WHICH ARE ADJACENT TO A LEADING EDGE SHALL BE NEATLY TAPED OFF AND PROTECTED FROM PRIMER AND TOPCOAT MATERIAL OR OVERSPRAY PRIMER SHALL BE APPLIED INTO SAW-CUT AREAS APPLY ELASTO -SHIELD ONTO SAW- CUT AREA FLOOD INTO SAW-CUT CAVITY WITH TROWEL OR PUTTY KNIFE AND SMOOTH LEVEL VERTICAL WILL REQUIRE OR MORE COATS UPON INITIAL SET OF ELASTO -SHIELD MATERIAL THE PROTECTIVE TAPE SHALL BE RAZOR-CUT AND REMOVED LEAVING A STRAIGHT AND NEAT LEADING EDGE TNEMEC ELASTO -SHIELD STANDARD LINING DETAILS LEADING EDGE TERMINATION DETAIL NO ELS - REV CMETAL EMBEDMENT SAWCUT TERMINATION ELASTO -SHIELD LINING SYSTEM EXISTING CONCRETE SUBSTRATE NOTES IF LINING IS TO BE CARRIED OVER METAL EMBEDMENT ? X ? SAW-CUT TOE-IN TERMINATION IS STILL REQUIRED TNEMEC ELASTO -SHIELD STANDARD LINING DETAILS TERMINATION DETAIL FOR EMBEDDED METALS NO ELS - REV CSERIES OR CHEMICAL RESISTANT NON-SAG CAULKING MATERIAL CANT COVE CL EXIST PIPE OR SLEEVE SCRIM OPTIONAL ELASTO -SHIELD LINING SYSTEM EXISTING CONCRETE SUBSTRATE NOTE ESTABLISH DEEPER SURFACE PROFILE ? AROUND O D OF PIPE PENETRATION TO LOCK LINING SYSTEM INTO SUBSTRATE TNEMEC ELASTO -SHIELD STANDARD LINING DETAILS SLEEVED OR NON-SLEEVED PIPE PENETRATION NO ELS - REV CFILL CONTROL JOINT WITH SERIES ELASTO -SHIELD LINING SYSTEM FILLER MATERIAL EXISTING CONCRETE SUBSTRATE CRACKS BETWEEN ? AND ? SHALL BE STRIPE COATED WITH SERIES TNEMEC ELASTO -SHIELD STANDARD LINING DETAILS CONTROL OR CONSTRUCTION JOINTS OR FOR NON-MOVING CRACKS NO ELS - REV CBACKER ROD COMPRESSED MIN AND SERIES OR FLEXIBLE JOINT SEALANT ELASTO -SHIELD LINING SYSTEM EXISTING CONCRETE SUBSTRATE EXISTING ISOLATION JOINT MATERIAL NOTE FLEXIBLE JOINT SEALANT WIDTH-TO -DEPTH RATIO SHOWN APPROXIMATELY TNEMEC ELASTO -SHIELD STANDARD LINING DETAILS EXPANSION JOINT TREATMENT DETAIL NO ELS - REV CELASTO -SHIELD FLOORING SYSTEM SERIES CHIP OUT ANGLE AROUND CRACK EXISTING CONCRETE SUBSTRATE JOINT OR CRACK NOTES PREPARE CRACK OR JOINT USING A CRACK CHASING TOOL OR CHIPPING GUN